Daviston’s concrete floor coatings
Flake, metallic, quartz, polished and sealed floors for Daviston homes and businesses. It is about 44 miles from the shop in Anniston, which is a routine run.
What Shanks coats in Daviston
Basements come up often here, and those are the floors where the moisture question gets answered before anything else is discussed. It is about 44 miles from the shop in Anniston, which is a routine run.
Tallapoosa County is lake country, so a lot of the work is outdoor: pool decks, covered porches and boathouse slabs that need a coating built for sun and standing water rather than for vehicles.
Whatever the slab turns out to be, the order of work does not change: grind it open, repair what is broken, then coat it. The twenty-two systems Shanks installs all sit on top of that same preparation.
Systems Daviston homeowners ask for
Garage Floor Epoxy
Ground, patched and coated so hot tires and dropped tools do not mark it.
Flake Epoxy
Vinyl chip in a pigmented base under clear. The most requested floor here.
Metallic Epoxy
Pearl pigment moved through resin so the floor reads like poured stone.
Grind and Seal
The concrete you already own, opened up, stained if you want, and sealed.
Patio Coatings
Textured, UV-stable finishes for porches, patios and pool surrounds.
Commercial Epoxy
Shop, warehouse and showroom floors specified for the actual use.
What decides whether it lasts
Why the topcoat matters more than the base
The layer you actually walk on, wash and scuff is the clear coat, not the color underneath. A cheap job leaves a standard epoxy as the top layer, and epoxy ambers in daylight, so a garage with a west-facing door turns yellow within a couple of years. A UV-stable polyaspartic or aliphatic urethane holds its color, cures fast enough to walk on the next day, and can be scuffed and recoated years later without disturbing what is underneath.
Moisture is the other half of it
Concrete is not waterproof. On a slab poured without a vapor barrier, or one sitting against damp ground, water vapor moves up through the pores continuously. Put a sealed coating over that and the vapor has nowhere to go, so it collects underneath and pushes the coating off in sheets. This is why a below-grade floor gets tested with a calcium chloride kit or a relative humidity probe before anyone quotes it, and why the honest answer is sometimes a mitigating primer first.
Anyone who quotes a concrete floor sight unseen is guessing, because the condition of the slab is most of the cost. Two garages of identical size can be a full day apart in preparation once you factor in old paint, glue, cracking and how much of the surface has broken down. Taylor looks at the floor, measures it, tells you what it needs, and then puts a real number in writing.
The owner does the work
Taylor quotes it, grinds it and coats it. On a job this size there is no crew to hand it off to, which is the whole point. Taylor Shanks trained with Brian Phillips, The Epoxy Dude, in southern Indiana, and he and Heather have run Shanks Concrete Coatings since 2025. Licensed and insured, Alabama #2602341.
If the honest answer for your Daviston floor is a cheaper system than the one you called about, that is what you will be told. More about how Shanks works.
See finished floorsWhich floor for which room
The hardest part for most homeowners is choosing between systems that all look good in photographs. Here is how they actually differ in use:
You like the concrete you already have
Grind and seal. The slab is opened up, optionally stained, and sealed. It costs less than a full coating system, it keeps the character of the concrete, and on a stamped patio or an older shop floor it is very often the better-looking answer.
It is outside
A textured patio coating with a UV-stable topcoat. Color choice matters more outdoors than anywhere else, because a dark smooth surface around a pool gets hot enough to be unpleasant barefoot in an Alabama July.
The slab is in rough shape
Restoration or a self-leveling overlay before anything decorative. A coating cannot bridge a surface that has broken down; the slab has to be rebuilt flat first, and then it takes any system you like.
You park a vehicle on it
Flake, almost every time. The chip field hides tire marks and dust, the texture stops it being slick when you track rain in, and the polyaspartic topcoat handles hot tires without softening. It is the most requested floor Shanks installs and it is the right call for the large majority of garages.
Other towns in Tallapoosa County
Shanks covers the whole county. If you are between two of these, you are still inside the radius, and the Tallapoosa County page lists every town.
New Site, AL
45 miles from the shop in Anniston.
Alexander City, AL
53 miles from the shop in Anniston.
Dadeville, AL
59 miles from the shop in Anniston.
Daviston questions
Do you actually work in Daviston?
Yes. It is about 44 miles from the shop in Anniston, which is a routine run. Daviston is inside the sixty-mile radius Shanks covers out of Anniston, and it is quoted at the same rate as a job in town.
How long will my floor take?
About three to four days for a standard two-car garage: grinding, repair and base coat, broadcast and scrape, then the topcoat. Bigger or more damaged floors take longer, and Taylor will give you the real schedule before starting.
Can you coat a basement here?
Often yes, but below-grade slabs get moisture-tested first. Vapor coming up through concrete will push a coating off no matter how good the prep was, so it is measured rather than assumed.
Will you look at it before quoting?
Always. The condition of the slab is most of the price, so a number over the phone would be a guess. Taylor looks at the floor, then gives you a real number in writing.
What is the most popular floor around here?
Flake, by a distance. It hides dust and tire marks, it is not slick when wet, and it suits both a garage and a finished basement.
Floors in Daviston
Square footage, what the room is used for, and what the slab looks like now. That is enough for a real number on a Daviston floor.