Home About
Services Services Residential Garage Floor Epoxy Flake Epoxy Metallic Epoxy Garage Floors Garage Floor Restoration Non-Slip Epoxy Floor Residential Concrete Floor Polishing Polyurethane Floors Quartz System Self-Leveling Overlays Sleeper System Floor Outdoor Patio Coatings Terrace Restoration Waterproofing Commercial Commercial Epoxy Flooring Commercial Flake Epoxy Commercial Metallic Floors Commercial Floor Painting Commercial Concrete Floor Polishing Prep Concrete Grinding Concrete Sealing Concrete Floor Prep Chemical-Resistant Novolac Epoxy
Areas Service Areas
Blount County, AL Blount County, AL Oneonta, AL
Calhoun County, AL Calhoun County, AL Anniston, AL Jacksonville, AL Oxford, AL Piedmont, AL
Carroll County, GA Carroll County, GA Carrollton, GA Mount Zion, GA Villa Rica, GA
Cherokee County, AL Cherokee County, AL Centre, AL
Clay County, AL Clay County, AL Lineville, AL
Cleburne County, AL Cleburne County, AL Edwardsville, AL Heflin, AL
DeKalb County, AL DeKalb County, AL Fort Payne, AL Rainsville, AL
Etowah County, AL Etowah County, AL Boaz, AL Gadsden, AL Glencoe, AL Hokes Bluff, AL Rainbow City, AL Southside, AL
Floyd County, GA Floyd County, GA Rome, GA
Haralson County, GA Haralson County, GA Bremen, GA Tallapoosa, GA
Jefferson County, AL Jefferson County, AL Birmingham, AL Clay, AL Fultondale, AL Gardendale, AL Irondale, AL Leeds, AL Mountain Brook, AL Pinson, AL Trussville, AL Vestavia Hills, AL Warrior, AL
Marshall County, AL Marshall County, AL Albertville, AL Guntersville, AL
Polk County, GA Polk County, GA Cedartown, GA
Randolph County, AL Randolph County, AL Roanoke, AL
Shelby County, AL Shelby County, AL Chelsea, AL Columbiana, AL Harpersville, AL Pelham, AL Vincent, AL Westover, AL Wilsonville, AL
St. Clair County, AL St. Clair County, AL Argo, AL Ashville, AL Margaret, AL Moody, AL Odenville, AL Pell City, AL Ragland, AL Springville, AL
Talladega County, AL Talladega County, AL Childersburg, AL Lincoln, AL Sylacauga, AL Talladega, AL
Tallapoosa County, AL Tallapoosa County, AL Alexander City, AL Dadeville, AL Daviston, AL New Site, AL
Gallery Blog Contact
Call · (256) 365-6535
Skip to content
Solid gray floor coating around blue pumps and black motors in a mechanical room
Jefferson County, AL

Irondale’s concrete floor coatings

Flake, metallic, quartz, polished and sealed floors for Irondale homes and businesses. It is about 50 miles from the shop in Anniston, which is a routine run.

What Shanks coats in Irondale

Most of what Shanks coats here is attached two-car garages, plus a steady run of basements that owners are finally finishing. It is about 50 miles from the shop in Anniston, which is a routine run.

Jefferson County is the far western end of the radius and the most varied. Mountain Brook and Vestavia basements tend to be decorative metallic and polished work; Trussville and Gardendale are newer garages taking flake; and there is a steady run of shop and warehouse floors around the industrial corridor.

Whatever the slab turns out to be, the order of work does not change: grind it open, repair what is broken, then coat it. The twenty-two systems Shanks installs all sit on top of that same preparation.

Beige house with a coated carport floor at dusk, and a black company trailer parked in the drive

Systems Irondale homeowners ask for

Light blue-gray coated pool deck around a swimming pool with a white slide and a white vinyl fence

Garage Floor Epoxy

Ground, patched and coated so hot tires and dropped tools do not mark it.

A worker rolling a glossy brown floor coating in an empty white room

Flake Epoxy

Vinyl chip in a pigmented base under clear. The most requested floor here.

Broken brown ceramic tile being pried off a floor beside a painted mural, with a hammer and dustpan

Metallic Epoxy

Pearl pigment moved through resin so the floor reads like poured stone.

Grind and Seal

The concrete you already own, opened up, stained if you want, and sealed.

Patio Coatings

Textured, UV-stable finishes for porches, patios and pool surrounds.

Commercial Epoxy

Shop, warehouse and showroom floors specified for the actual use.

What decides whether it lasts

Why the topcoat matters more than the base

The layer you actually walk on, wash and scuff is the clear coat, not the color underneath. A cheap job leaves a standard epoxy as the top layer, and epoxy ambers in daylight, so a garage with a west-facing door turns yellow within a couple of years. A UV-stable polyaspartic or aliphatic urethane holds its color, cures fast enough to walk on the next day, and can be scuffed and recoated years later without disturbing what is underneath.

Why the grinder decides everything

Almost every failed garage floor starts the same way: a coating rolled onto concrete that was never opened up. A troweled slab has a tight, closed surface, and resin sitting on top of it has nothing to grip. Diamond grinding cuts that skin away and leaves a profile like fine sandpaper, which is what a coating actually bonds into. It is the loudest, dirtiest and least glamorous day of the job, and it is the one that decides whether the floor is still tight in ten years.

If a grind and seal will serve your room better than a full flake system, that is what you will be told, even though it is the smaller job. The same goes for timing: a slab poured last month is not ready, and coating green concrete is one of the few genuinely unfixable mistakes in this trade. Waiting a few weeks costs nothing; getting it wrong costs the whole floor.

The owner does the work

There is no salesman in the middle here. Taylor looks at the floor, tells you what it needs, and then does that work himself. Taylor Shanks trained with Brian Phillips, The Epoxy Dude, in southern Indiana, and he and Heather have run Shanks Concrete Coatings since 2025. Licensed and insured, Alabama #2602341.

If the honest answer for your Irondale floor is a cheaper system than the one you called about, that is what you will be told. More about how Shanks works.

See finished floors

Which floor for which room

Most people call about one system and end up with a different one, because the room decides more than the brochure does. A quick way to narrow it down:

It is a finished room you look at

Metallic, if you want the floor to be the feature, or polished concrete if you want it quiet. Metallic gives you flowing depth that no two floors share; polishing gives you the slab itself, refined, with nothing on top that can ever peel.

It gets wet or greasy

Quartz or a non-slip build. Both put graded aggregate into the surface so there is real traction underfoot, and both can be coved up the wall and sloped to a drain so the room can be properly washed down rather than just mopped.

You like the concrete you already have

Grind and seal. The slab is opened up, optionally stained, and sealed. It costs less than a full coating system, it keeps the character of the concrete, and on a stamped patio or an older shop floor it is very often the better-looking answer.

It is outside

A textured patio coating with a UV-stable topcoat. Color choice matters more outdoors than anywhere else, because a dark smooth surface around a pool gets hot enough to be unpleasant barefoot in an Alabama July.

Read the detail on each system

Other towns in Jefferson County

Shanks covers the whole county. If you are between two of these, you are still inside the radius, and the Jefferson County page lists every town.

Glossy light gray solid color floor in a white metal shop, running toward an open bay

Trussville, AL

43 miles from the shop in Anniston.

Leeds, AL

45 miles from the shop in Anniston.

Clay, AL

46 miles from the shop in Anniston.

Pinson, AL

49 miles from the shop in Anniston.

Mountain Brook, AL

55 miles from the shop in Anniston.

Irondale questions

Do you actually work in Irondale?

Yes. It is about 50 miles from the shop in Anniston, which is a routine run. Irondale is inside the sixty-mile radius Shanks covers out of Anniston, and it is quoted at the same rate as a job in town.

How long will my floor take?

About three to four days for a standard two-car garage: grinding, repair and base coat, broadcast and scrape, then the topcoat. Bigger or more damaged floors take longer, and Taylor will give you the real schedule before starting.

Can you coat a basement here?

Often yes, but below-grade slabs get moisture-tested first. Vapor coming up through concrete will push a coating off no matter how good the prep was, so it is measured rather than assumed.

Will you look at it before quoting?

Always. The condition of the slab is most of the price, so a number over the phone would be a guess. Taylor looks at the floor, then gives you a real number in writing.

What is the most popular floor around here?

Flake, by a distance. It hides dust and tire marks, it is not slick when wet, and it suits both a garage and a finished basement.

Floors in Irondale

Square footage, what the room is used for, and what the slab looks like now. That is enough for a real number on a Irondale floor.