Home About
Services Services Residential Garage Floor Epoxy Flake Epoxy Metallic Epoxy Garage Floors Garage Floor Restoration Non-Slip Epoxy Floor Residential Concrete Floor Polishing Polyurethane Floors Quartz System Self-Leveling Overlays Sleeper System Floor Outdoor Patio Coatings Terrace Restoration Waterproofing Commercial Commercial Epoxy Flooring Commercial Flake Epoxy Commercial Metallic Floors Commercial Floor Painting Commercial Concrete Floor Polishing Prep Concrete Grinding Concrete Sealing Concrete Floor Prep Chemical-Resistant Novolac Epoxy
Areas Service Areas
Blount County, AL Blount County, AL Oneonta, AL
Calhoun County, AL Calhoun County, AL Anniston, AL Jacksonville, AL Oxford, AL Piedmont, AL
Carroll County, GA Carroll County, GA Carrollton, GA Mount Zion, GA Villa Rica, GA
Cherokee County, AL Cherokee County, AL Centre, AL
Clay County, AL Clay County, AL Lineville, AL
Cleburne County, AL Cleburne County, AL Edwardsville, AL Heflin, AL
DeKalb County, AL DeKalb County, AL Fort Payne, AL Rainsville, AL
Etowah County, AL Etowah County, AL Boaz, AL Gadsden, AL Glencoe, AL Hokes Bluff, AL Rainbow City, AL Southside, AL
Floyd County, GA Floyd County, GA Rome, GA
Haralson County, GA Haralson County, GA Bremen, GA Tallapoosa, GA
Jefferson County, AL Jefferson County, AL Birmingham, AL Clay, AL Fultondale, AL Gardendale, AL Irondale, AL Leeds, AL Mountain Brook, AL Pinson, AL Trussville, AL Vestavia Hills, AL Warrior, AL
Marshall County, AL Marshall County, AL Albertville, AL Guntersville, AL
Polk County, GA Polk County, GA Cedartown, GA
Randolph County, AL Randolph County, AL Roanoke, AL
Shelby County, AL Shelby County, AL Chelsea, AL Columbiana, AL Harpersville, AL Pelham, AL Vincent, AL Westover, AL Wilsonville, AL
St. Clair County, AL St. Clair County, AL Argo, AL Ashville, AL Margaret, AL Moody, AL Odenville, AL Pell City, AL Ragland, AL Springville, AL
Talladega County, AL Talladega County, AL Childersburg, AL Lincoln, AL Sylacauga, AL Talladega, AL
Tallapoosa County, AL Tallapoosa County, AL Alexander City, AL Dadeville, AL Daviston, AL New Site, AL
Gallery Blog Contact
Call · (256) 365-6535
Skip to content
Utility room with two maroon furnaces, a gray coated lower landing, and vacuum hoses in the foreground
Etowah County, AL

Glencoe’s concrete floor coatings

Flake, metallic, quartz, polished and sealed floors for Glencoe homes and businesses. It is about 20 miles from the shop in Anniston, which is a routine run.

What Shanks coats in Glencoe

A lot of the calls here are older slabs that have never had anything on them, where a grind and seal does more for the room than a decorative system would. It is about 20 miles from the shop in Anniston, which is a routine run.

Etowah County has a lot of split-level and walk-out basement housing cut into the slopes above the river. Those below-grade slabs are the ones most likely to be moving vapor, so they get a moisture test before a quote rather than an apology afterwards.

Whatever the slab turns out to be, the order of work does not change: grind it open, repair what is broken, then coat it. The twenty-two systems Shanks installs all sit on top of that same preparation.

Gray flake pool deck around a swimming pool, enclosed by a white fence

Systems Glencoe homeowners ask for

Bare concrete slab in a pine-walled barn shop with the roll-up door open and a grinder on the floor

Garage Floor Epoxy

Ground, patched and coated so hot tires and dropped tools do not mark it.

Dark gray flake floor with a matching cove base in a small OSB-lined room

Flake Epoxy

Vinyl chip in a pigmented base under clear. The most requested floor here.

Pewter and silver metallic epoxy floor swirling across a gray-walled room with white doors

Metallic Epoxy

Pearl pigment moved through resin so the floor reads like poured stone.

Grind and Seal

The concrete you already own, opened up, stained if you want, and sealed.

Patio Coatings

Textured, UV-stable finishes for porches, patios and pool surrounds.

Commercial Epoxy

Shop, warehouse and showroom floors specified for the actual use.

What decides whether it lasts

What repair actually involves

Cracks get chased out into a V with a saw rather than simply filled, so the repair has shoulders to hold onto, then filled with a rigid polyurea that can be ground flush the same day. Spalled edges near a garage door, where water has sat and frozen for a few winters, are rebuilt with a polymer-modified patch. None of this shows in the finished floor, which is precisely why it gets skipped by people quoting the cheapest number.

Moisture is the other half of it

Concrete is not waterproof. On a slab poured without a vapor barrier, or one sitting against damp ground, water vapor moves up through the pores continuously. Put a sealed coating over that and the vapor has nowhere to go, so it collects underneath and pushes the coating off in sheets. This is why a below-grade floor gets tested with a calcium chloride kit or a relative humidity probe before anyone quotes it, and why the honest answer is sometimes a mitigating primer first.

If a grind and seal will serve your room better than a full flake system, that is what you will be told, even though it is the smaller job. The same goes for timing: a slab poured last month is not ready, and coating green concrete is one of the few genuinely unfixable mistakes in this trade. Waiting a few weeks costs nothing; getting it wrong costs the whole floor.

The owner does the work

Taylor quotes it, grinds it and coats it. On a job this size there is no crew to hand it off to, which is the whole point. Taylor Shanks trained with Brian Phillips, The Epoxy Dude, in southern Indiana, and he and Heather have run Shanks Concrete Coatings since 2025. Licensed and insured, Alabama #2602341.

If the honest answer for your Glencoe floor is a cheaper system than the one you called about, that is what you will be told. More about how Shanks works.

See finished floors

Which floor for which room

If you are trying to work out which floor you want before anyone comes out, this is the short version:

It is a finished room you look at

Metallic, if you want the floor to be the feature, or polished concrete if you want it quiet. Metallic gives you flowing depth that no two floors share; polishing gives you the slab itself, refined, with nothing on top that can ever peel.

It gets wet or greasy

Quartz or a non-slip build. Both put graded aggregate into the surface so there is real traction underfoot, and both can be coved up the wall and sloped to a drain so the room can be properly washed down rather than just mopped.

You like the concrete you already have

Grind and seal. The slab is opened up, optionally stained, and sealed. It costs less than a full coating system, it keeps the character of the concrete, and on a stamped patio or an older shop floor it is very often the better-looking answer.

It is outside

A textured patio coating with a UV-stable topcoat. Color choice matters more outdoors than anywhere else, because a dark smooth surface around a pool gets hot enough to be unpleasant barefoot in an Alabama July.

Read the detail on each system

Other towns in Etowah County

Shanks covers the whole county. If you are between two of these, you are still inside the radius, and the Etowah County page lists every town.

Warm brown stained and sealed floor in a double-height room with a loft rail and ceiling fan

Southside, AL

19 miles from the shop in Anniston.

Hokes Bluff, AL

22 miles from the shop in Anniston.

Rainbow City, AL

24 miles from the shop in Anniston.

Gadsden, AL

26 miles from the shop in Anniston.

Boaz, AL

41 miles from the shop in Anniston.

Glencoe questions

Do you actually work in Glencoe?

Yes. It is about 20 miles from the shop in Anniston, which is a routine run. Glencoe is inside the sixty-mile radius Shanks covers out of Anniston, and it is quoted at the same rate as a job in town.

How long will my floor take?

About three to four days for a standard two-car garage: grinding, repair and base coat, broadcast and scrape, then the topcoat. Bigger or more damaged floors take longer, and Taylor will give you the real schedule before starting.

Can you coat a basement here?

Often yes, but below-grade slabs get moisture-tested first. Vapor coming up through concrete will push a coating off no matter how good the prep was, so it is measured rather than assumed.

Will you look at it before quoting?

Always. The condition of the slab is most of the price, so a number over the phone would be a guess. Taylor looks at the floor, then gives you a real number in writing.

What is the most popular floor around here?

Flake, by a distance. It hides dust and tire marks, it is not slick when wet, and it suits both a garage and a finished basement.

Floors in Glencoe

Square footage, what the room is used for, and what the slab looks like now. That is enough for a real number on a Glencoe floor.