Home About
Services Services Residential Garage Floor Epoxy Flake Epoxy Metallic Epoxy Garage Floors Garage Floor Restoration Non-Slip Epoxy Floor Residential Concrete Floor Polishing Polyurethane Floors Quartz System Self-Leveling Overlays Sleeper System Floor Outdoor Patio Coatings Terrace Restoration Waterproofing Commercial Commercial Epoxy Flooring Commercial Flake Epoxy Commercial Metallic Floors Commercial Floor Painting Commercial Concrete Floor Polishing Prep Concrete Grinding Concrete Sealing Concrete Floor Prep Chemical-Resistant Novolac Epoxy
Areas Service Areas
Blount County, AL Blount County, AL Oneonta, AL
Calhoun County, AL Calhoun County, AL Anniston, AL Jacksonville, AL Oxford, AL Piedmont, AL
Carroll County, GA Carroll County, GA Carrollton, GA Mount Zion, GA Villa Rica, GA
Cherokee County, AL Cherokee County, AL Centre, AL
Clay County, AL Clay County, AL Lineville, AL
Cleburne County, AL Cleburne County, AL Edwardsville, AL Heflin, AL
DeKalb County, AL DeKalb County, AL Fort Payne, AL Rainsville, AL
Etowah County, AL Etowah County, AL Boaz, AL Gadsden, AL Glencoe, AL Hokes Bluff, AL Rainbow City, AL Southside, AL
Floyd County, GA Floyd County, GA Rome, GA
Haralson County, GA Haralson County, GA Bremen, GA Tallapoosa, GA
Jefferson County, AL Jefferson County, AL Birmingham, AL Clay, AL Fultondale, AL Gardendale, AL Irondale, AL Leeds, AL Mountain Brook, AL Pinson, AL Trussville, AL Vestavia Hills, AL Warrior, AL
Marshall County, AL Marshall County, AL Albertville, AL Guntersville, AL
Polk County, GA Polk County, GA Cedartown, GA
Randolph County, AL Randolph County, AL Roanoke, AL
Shelby County, AL Shelby County, AL Chelsea, AL Columbiana, AL Harpersville, AL Pelham, AL Vincent, AL Westover, AL Wilsonville, AL
St. Clair County, AL St. Clair County, AL Argo, AL Ashville, AL Margaret, AL Moody, AL Odenville, AL Pell City, AL Ragland, AL Springville, AL
Talladega County, AL Talladega County, AL Childersburg, AL Lincoln, AL Sylacauga, AL Talladega, AL
Tallapoosa County, AL Tallapoosa County, AL Alexander City, AL Dadeville, AL Daviston, AL New Site, AL
Gallery Blog Contact
Call · (256) 365-6535
Skip to content
Glossy tan sealed floor in a room with a pine plank ceiling and large dark windows
Commercial · Anniston, Alabama

Commercial concrete polishing

A hard, dust-free, low-maintenance floor made from the slab already in the building.

The build-up, step by step

Every commercial concrete floor polishing job Shanks installs follows the same order, because skipping a stage is how floors fail. Taylor is on site for all of it.

Flatten

Metal-bond diamonds flatten the floor and set how much aggregate shows.

Densify

Lithium silicate hardens the surface and stops the dusting that raw concrete does under traffic.

Polish

Resin passes to the specified gloss level.

Guard

A penetrating guard for stain resistance, with no film to peel under a forklift.

Right room, right system

Warehouses, retail, breweries, schools and any large floor where long-term maintenance cost matters more than color.

Where it is the wrong call

Slabs that are heavily patched, badly stained or have lost their surface ; an overlay comes first.

Back in service: Back in service immediately. There is no film to cure.

Compare the other systems
Warm brown stained and sealed floor in a double-height room with a loft rail and ceiling fan

Why this floor costs what it costs

Two floors the same size can land a long way apart on price. These are the variables that decide it:

Size and shape

Bigger floors cost less per square foot, because the setup, the mixing and the cleanup are much the same whether the room is 400 or 1,400 square feet. Cut-up rooms with lots of edges take longer than open ones.

Which system you choose

Build thickness and the chemistry of the topcoat are the two biggest material costs. A heavier commercial build genuinely costs more than a residential one.

Access

A walk-out basement with a door at grade is straightforward. Carrying equipment down a flight of stairs, or working around a building that has to stay open, adds time.

Condition of the slab

A clean, sound slab grinds in a morning. One carrying old paint, carpet glue, or a failed coating can take a full day longer before anything can be applied.

Wood-look stamped concrete on a covered porch with stone-clad posts and a chandelier

What Alabama slabs do

Most of the housing around Anniston, Oxford and Jacksonville was poured between the sixties and the eighties, and those slabs were hard-troweled to a tight, closed surface. They look clean and they take a coating badly until they are properly ground, which is why a store-bought kit so often lets go here within a year.

Newer construction around Trussville, Chelsea and Springville is usually a clean, flat pour that takes a coating beautifully, as long as the concrete has had its twenty-eight days. Coating green concrete is one of the few genuinely unfixable mistakes in this trade.

Where the trailer goes

What the days actually look like

People are usually more anxious about the disruption than the floor. Here is what the days actually look like:

Planning the shutdown

The sequence is built around your operating hours first. Most commercial floors here are done in sections or overnight so the business keeps running.

Clearing and protection

Racking, stock and equipment move out of the working section, and adjacent areas are sheeted so dust and overspray stay put.

Prep and application

Grinding or shot blasting, repair, then the build. Each section gets handed back on a stated day, not a vague one.

Return to service

Foot traffic in about 24 hours, racking and vehicles at the full cure window for the system chosen.

Keeping it looking new

An auto-scrubber or a flat mop with a neutral cleaner, and nothing acidic. There is no film to strip, no wax and no recoating cycle, which is the whole reason large buildings choose it. A periodic burnish brings the sheen back up if traffic has flattened it.

Anything Taylor installs comes with a walk-through at handover covering exactly this, plus what to avoid in the first two weeks while the coating reaches full hardness. If something does go wrong later, tell him about it rather than living with it.

The owner is the installer

Shanks Concrete Coatings is Taylor and Heather Shanks, working out of Anniston. Taylor trained directly with Brian Phillips, The Epoxy Dude, in southern Indiana, and he runs the grinder and pulls the squeegee on every job himself. Licensed and insured, Alabama #2602341.

If a commercial concrete floor polishing floor is not the right answer for your room, he will tell you that on the first visit rather than sell it to you. More about how Shanks works, or send over the details of your floor.

Commercial Concrete Floor Polishing questions

Why polish instead of coat?

There is nothing to delaminate. A polished slab cannot peel because it is not a layer, which is why big-box retail and warehouses default to it.

How is it maintained?

An auto-scrubber with a neutral cleaner. No stripping, no waxing, no recoating cycle.

Will the joints still show?

Yes, and they can be filled with a semi-rigid filler so wheels roll across them without chipping the edges.

Can it be done while we operate?

Yes, in sections. It is dust-controlled and there are no solvent odors to work around.

Is it cheaper than a coating over the life of the floor?

Generally yes, and that is why warehouses default to it. There is no recoating cycle and no stripping and waxing, so the ongoing cost is an auto-scrubber and a neutral cleaner.

Four questions worth asking any installer

Ask these of Shanks and of whoever else you are talking to. The answers separate a floor that lasts from one that looks good for a season, and a straight installer will not mind being asked.

How are you preparing the slab?

The only acceptable answers involve a diamond grinder or a shot blaster. Acid etching and a scrub with degreaser is not preparation, and it is the single most common reason a coating lets go.

Are you testing for moisture?

On any basement or ground-level slab this should be a yes with a number attached. Vapor pressure will push a coating off no matter how good the product is.

Who is actually on my floor?

Worth asking whoever quotes you. With Shanks the person who quotes it is the person who grinds it and coats it, and that is not true everywhere.

What is the topcoat?

A UV-stable polyaspartic or aliphatic urethane holds its color. A cheap job leaves a standard epoxy as the top layer, and it will amber in daylight within a year or two.

Other systems for the same room

Commercial Concrete Floor Polishing is one of twenty-two systems Shanks installs. If the room is telling you something different, these are the closest alternatives, and Taylor will happily point you at the cheaper one if it is the right answer.

High-gloss light gray floor reflecting the ceiling lights of a white metal shop

Commercial Epoxy

Another system Shanks installs across the same sixty-mile area.

Gray and white flake floor in a garage with charcoal walls and two water heaters in the corner

Commercial Flake

Another system Shanks installs across the same sixty-mile area.

Novolac Epoxy

Another system Shanks installs across the same sixty-mile area.

Talk to the person doing the work

Square footage, what the room is used for, and what the slab looks like now. That is enough to get you a real number on commercial concrete floor polishing.