
Garage floor epoxy in northeast Alabama
A ground, patched and coated garage slab that shrugs off hot tires, dropped tools and road salt.
The build-up, step by step
Every garage floor epoxy job Shanks installs follows the same order, because skipping a stage is how floors fail. Taylor is on site for all of it.
Diamond grind
The slab is opened with metal-bond diamonds until the troweled skin is gone and the surface reads like fine sandpaper. Old paint, glue and sealer come off in this pass.
Crack and joint repair
Cracks get chased out and filled with a rigid polyurea that can be ground flush. Spalled edges near the door get rebuilt so the coating has something solid to terminate on.
Pigmented base
A 100% solids epoxy base goes down at roughly 10 to 12 mils, thick enough to bond into the profile and carry the color.
Broadcast and topcoat
Vinyl flake is thrown to refusal, scraped back the following morning, then locked under a clear polyaspartic that carries the gloss and the UV stability.
Right room, right system
Attached and detached garages, workshop bays, and any slab that sees a vehicle. It handles point loads from a jack stand and it does not soften under a hot tire the way a one-part paint does.
Where it is the wrong call
A slab with active moisture coming up through it, or one poured within the last month. Both need to be dealt with before anything bonds.
Back in service: Foot traffic the next day; vehicles at five to seven days.
Compare the other systems
Why this floor costs what it costs
The square footage is the easy part. What changes a quote from one job to the next is almost always the condition of the slab underneath:
Condition of the slab
A clean, sound slab grinds in a morning. One carrying old paint, carpet glue, or a failed coating can take a full day longer before anything can be applied.
How much repair it needs
Cracks, spalled edges, pitting and old anchor holes are filled and ground flush before coating. A slab that needs a lot of this can add a day on its own.
Size and shape
Bigger floors cost less per square foot, because the setup, the mixing and the cleanup are much the same whether the room is 400 or 1,400 square feet. Cut-up rooms with lots of edges take longer than open ones.
Which system you choose
Build thickness and the chemistry of the topcoat are the two biggest material costs. A heavier commercial build genuinely costs more than a residential one.

What Alabama slabs do
Out toward Gadsden, Southside and Pell City there are a lot of walk-out basements cut into a hillside. Those slabs sit against earth on three sides, so they get moisture-tested before a quote rather than after a failure.
Alabama humidity is the quiet variable in this work. Resin cures on a temperature and dew-point window, so a floor is scheduled around the weather rather than squeezed in before a storm rolls over Talladega.
Where the trailer goesWhat the days actually look like
Knowing the shape of the week takes most of the worry out of it. A typical job runs like this:
Before Taylor arrives
The room has to be completely empty, including anything mounted low on the walls if the coating is being coved up. Freezers and fridges need somewhere else to live for a few days, and the breaker for the room should be reachable.
Grinding day
The loudest day. Grinders run on HEPA vacuums so dust stays contained, but it is not quiet, and it is worth knowing that in advance if somebody works from home.
Coating days
Once resin is down, the room is closed. Pets and children need to stay out, and doors get taped so nobody wanders in overnight.
Getting it back
Foot traffic the next morning. Vehicles wait the full window, and putting a car back early is the one shortcut that visibly damages a new floor.
Keeping it looking new
Sweep it, and mop it with warm water and a neutral cleaner. Skip anything with citrus or ammonia, since both attack the topcoat over time. Felt pads under anything with a metal foot, and a mat under the jack stand if you work on vehicles. Years down the road the clear coat can be scuffed and recoated, which brings the gloss back without touching the flake underneath.
Anything Taylor installs comes with a walk-through at handover covering exactly this, plus what to avoid in the first two weeks while the coating reaches full hardness. If something does go wrong later, tell him about it rather than living with it.
The owner is the installer
Shanks Concrete Coatings is Taylor and Heather Shanks, working out of Anniston. Taylor trained directly with Brian Phillips, The Epoxy Dude, in southern Indiana, and he runs the grinder and pulls the squeegee on every job himself. Licensed and insured, Alabama #2602341.
If a garage floor epoxy floor is not the right answer for your room, he will tell you that on the first visit rather than sell it to you. More about how Shanks works, or send over the details of your floor.
Garage Floor Epoxy questions
Will hot tires lift it?
Not with this build-up. Hot tire pickup happens when a thin one-part coating softens and releases from an un-ground slab. A ground profile plus a 100% solids base plus a polyaspartic topcoat gives the tire nothing to pull on.
Can you do the walls too?
The flake can be coved up the wall four to six inches so there is no dirt-catching joint at the floor line. It has to be decided before the grind, because the wall gets prepped at the same time.
What if my garage has a drain?
It gets masked and the coating is terminated cleanly at the grate rather than run into it.
How long am I out of my garage?
About three to four days on a standard two-car, and it needs to be emptied before the grinder shows up.
Do you coat the apron outside the door too?
It can be, but it is a different exposure: an apron takes direct sun, standing water and freeze-thaw, so it wants a UV-stable topcoat and often a bit more texture. Taylor will price it separately so you can decide.
Four questions worth asking any installer
Ask these of Shanks and of whoever else you are talking to. The answers separate a floor that lasts from one that looks good for a season, and a straight installer will not mind being asked.
How are you preparing the slab?
The only acceptable answers involve a diamond grinder or a shot blaster. Acid etching and a scrub with degreaser is not preparation, and it is the single most common reason a coating lets go.
Are you testing for moisture?
On any basement or ground-level slab this should be a yes with a number attached. Vapor pressure will push a coating off no matter how good the product is.
Who is actually on my floor?
Worth asking whoever quotes you. With Shanks the person who quotes it is the person who grinds it and coats it, and that is not true everywhere.
What is the topcoat?
A UV-stable polyaspartic or aliphatic urethane holds its color. A cheap job leaves a standard epoxy as the top layer, and it will amber in daylight within a year or two.
Other systems for the same room
Garage Floor Epoxy is one of twenty-two systems Shanks installs. If the room is telling you something different, these are the closest alternatives, and Taylor will happily point you at the cheaper one if it is the right answer.

Flake Epoxy
Another system Shanks installs across the same sixty-mile area.

Metallic Epoxy
Another system Shanks installs across the same sixty-mile area.
Grind and Seal
Another system Shanks installs across the same sixty-mile area.
Tell Taylor about your floor
Square footage, what the room is used for, and what the slab looks like now. That is enough to get you a real number on garage floor epoxy.