Alexander City’s concrete floor coatings
Flake, metallic, quartz, polished and sealed floors for Alexander City homes and businesses. It is about 53 miles from the shop in Anniston, which is a routine run.
What Shanks coats in Alexander City
Basements come up often here, and those are the floors where the moisture question gets answered before anything else is discussed. It is about 53 miles from the shop in Anniston, which is a routine run.
Tallapoosa County is lake country, so a lot of the work is outdoor: pool decks, covered porches and boathouse slabs that need a coating built for sun and standing water rather than for vehicles.
Whatever the slab turns out to be, the order of work does not change: grind it open, repair what is broken, then coat it. The twenty-two systems Shanks installs all sit on top of that same preparation.
Systems Alexander City homeowners ask for
Garage Floor Epoxy
Ground, patched and coated so hot tires and dropped tools do not mark it.
Flake Epoxy
Vinyl chip in a pigmented base under clear. The most requested floor here.
Metallic Epoxy
Pearl pigment moved through resin so the floor reads like poured stone.
Grind and Seal
The concrete you already own, opened up, stained if you want, and sealed.
Patio Coatings
Textured, UV-stable finishes for porches, patios and pool surrounds.
Commercial Epoxy
Shop, warehouse and showroom floors specified for the actual use.
What decides whether it lasts
Why the topcoat matters more than the base
The layer you actually walk on, wash and scuff is the clear coat, not the color underneath. A cheap job leaves a standard epoxy as the top layer, and epoxy ambers in daylight, so a garage with a west-facing door turns yellow within a couple of years. A UV-stable polyaspartic or aliphatic urethane holds its color, cures fast enough to walk on the next day, and can be scuffed and recoated years later without disturbing what is underneath.
What repair actually involves
Cracks get chased out into a V with a saw rather than simply filled, so the repair has shoulders to hold onto, then filled with a rigid polyurea that can be ground flush the same day. Spalled edges near a garage door, where water has sat and frozen for a few winters, are rebuilt with a polymer-modified patch. None of this shows in the finished floor, which is precisely why it gets skipped by people quoting the cheapest number.
If a grind and seal will serve your room better than a full flake system, that is what you will be told, even though it is the smaller job. The same goes for timing: a slab poured last month is not ready, and coating green concrete is one of the few genuinely unfixable mistakes in this trade. Waiting a few weeks costs nothing; getting it wrong costs the whole floor.
The owner does the work
There is no salesman in the middle here. Taylor looks at the floor, tells you what it needs, and then does that work himself. Taylor Shanks trained with Brian Phillips, The Epoxy Dude, in southern Indiana, and he and Heather have run Shanks Concrete Coatings since 2025. Licensed and insured, Alabama #2602341.
If the honest answer for your Alexander City floor is a cheaper system than the one you called about, that is what you will be told. More about how Shanks works.
See finished floorsWhich floor for which room
If you are trying to work out which floor you want before anyone comes out, this is the short version:
It is a finished room you look at
Metallic, if you want the floor to be the feature, or polished concrete if you want it quiet. Metallic gives you flowing depth that no two floors share; polishing gives you the slab itself, refined, with nothing on top that can ever peel.
It gets wet or greasy
Quartz or a non-slip build. Both put graded aggregate into the surface so there is real traction underfoot, and both can be coved up the wall and sloped to a drain so the room can be properly washed down rather than just mopped.
You like the concrete you already have
Grind and seal. The slab is opened up, optionally stained, and sealed. It costs less than a full coating system, it keeps the character of the concrete, and on a stamped patio or an older shop floor it is very often the better-looking answer.
It is outside
A textured patio coating with a UV-stable topcoat. Color choice matters more outdoors than anywhere else, because a dark smooth surface around a pool gets hot enough to be unpleasant barefoot in an Alabama July.
Other towns in Tallapoosa County
Shanks covers the whole county. If you are between two of these, you are still inside the radius, and the Tallapoosa County page lists every town.
Daviston, AL
44 miles from the shop in Anniston.
New Site, AL
45 miles from the shop in Anniston.
Dadeville, AL
59 miles from the shop in Anniston.
Alexander City questions
Do you actually work in Alexander City?
Yes. It is about 53 miles from the shop in Anniston, which is a routine run. Alexander City is inside the sixty-mile radius Shanks covers out of Anniston, and it is quoted at the same rate as a job in town.
How long will my floor take?
About three to four days for a standard two-car garage: grinding, repair and base coat, broadcast and scrape, then the topcoat. Bigger or more damaged floors take longer, and Taylor will give you the real schedule before starting.
Can you coat a basement here?
Often yes, but below-grade slabs get moisture-tested first. Vapor coming up through concrete will push a coating off no matter how good the prep was, so it is measured rather than assumed.
Will you look at it before quoting?
Always. The condition of the slab is most of the price, so a number over the phone would be a guess. Taylor looks at the floor, then gives you a real number in writing.
What is the most popular floor around here?
Flake, by a distance. It hides dust and tire marks, it is not slick when wet, and it suits both a garage and a finished basement.
Floors in Alexander City
Square footage, what the room is used for, and what the slab looks like now. That is enough for a real number on a Alexander City floor.