Home About
Services Services Residential Garage Floor Epoxy Flake Epoxy Metallic Epoxy Garage Floors Garage Floor Restoration Non-Slip Epoxy Floor Residential Concrete Floor Polishing Polyurethane Floors Quartz System Self-Leveling Overlays Sleeper System Floor Outdoor Patio Coatings Terrace Restoration Waterproofing Commercial Commercial Epoxy Flooring Commercial Flake Epoxy Commercial Metallic Floors Commercial Floor Painting Commercial Concrete Floor Polishing Prep Concrete Grinding Concrete Sealing Concrete Floor Prep Chemical-Resistant Novolac Epoxy
Areas Service Areas
Blount County, AL Blount County, AL Oneonta, AL
Calhoun County, AL Calhoun County, AL Anniston, AL Jacksonville, AL Oxford, AL Piedmont, AL
Carroll County, GA Carroll County, GA Carrollton, GA Mount Zion, GA Villa Rica, GA
Cherokee County, AL Cherokee County, AL Centre, AL
Clay County, AL Clay County, AL Lineville, AL
Cleburne County, AL Cleburne County, AL Edwardsville, AL Heflin, AL
DeKalb County, AL DeKalb County, AL Fort Payne, AL Rainsville, AL
Etowah County, AL Etowah County, AL Boaz, AL Gadsden, AL Glencoe, AL Hokes Bluff, AL Rainbow City, AL Southside, AL
Floyd County, GA Floyd County, GA Rome, GA
Haralson County, GA Haralson County, GA Bremen, GA Tallapoosa, GA
Jefferson County, AL Jefferson County, AL Birmingham, AL Clay, AL Fultondale, AL Gardendale, AL Irondale, AL Leeds, AL Mountain Brook, AL Pinson, AL Trussville, AL Vestavia Hills, AL Warrior, AL
Marshall County, AL Marshall County, AL Albertville, AL Guntersville, AL
Polk County, GA Polk County, GA Cedartown, GA
Randolph County, AL Randolph County, AL Roanoke, AL
Shelby County, AL Shelby County, AL Chelsea, AL Columbiana, AL Harpersville, AL Pelham, AL Vincent, AL Westover, AL Wilsonville, AL
St. Clair County, AL St. Clair County, AL Argo, AL Ashville, AL Margaret, AL Moody, AL Odenville, AL Pell City, AL Ragland, AL Springville, AL
Talladega County, AL Talladega County, AL Childersburg, AL Lincoln, AL Sylacauga, AL Talladega, AL
Tallapoosa County, AL Tallapoosa County, AL Alexander City, AL Dadeville, AL Daviston, AL New Site, AL
Gallery Blog Contact
Call · (256) 365-6535
Skip to content

Coating a Garage Floor in an Alabama Winter

“Should I just wait until spring?”

Taylor gets that question every November, usually from somebody who has been meaning to do the garage all year and has decided the weather has made the decision for them. The short answer is no, you do not have to wait. The longer answer is that winter changes how the job has to be run, and a contractor who does not change anything about his process between July and January is the one you should be worried about.

Here is what cold actually does to a resin floor, and what has to happen for a January install to come out as well as a June one.

Cold slows the reaction and thickens the material

A two-part resin cures by chemical reaction, and reaction rate depends on temperature. The working rule is that the rate roughly halves for every eighteen degrees Fahrenheit you drop. A floor that would be hard enough to walk on in twelve hours at eighty degrees might want twenty-four at sixty, and considerably longer below that.

That part is inconvenient rather than dangerous. The second effect is the one that causes damage.

Cold resin is thick. Viscosity climbs sharply as temperature falls, and a thick resin does three things badly. It does not flow out level, so roller marks and squeegee lines stay in the finished surface instead of self-leveling away. It does not penetrate into the ground profile of the slab, which is the entire mechanism by which the coating holds on. And it traps air, because bubbles worked into a thick mix cannot rise out of it before it gels.

There is a temperature floor, and it is a real number

Every resin product has a minimum application temperature printed on its data sheet. For most epoxies it sits around fifty degrees Fahrenheit. Some cold-weather and polyaspartic formulations go lower, into the thirties and forties, which is one of the reasons the topcoat chemistry matters as much in winter as it does for UV outdoors.

Below that number the manufacturer is not being cautious. The reaction can stall, and a stalled epoxy does not simply cure slowly and catch up later. It can stay soft indefinitely, remaining tacky and uncured in a way that cannot be fixed by waiting for warmer weather. That floor comes back off.

Slab temperature, not air temperature

This is the part most people have never thought about, and it is the single most useful thing in this post.

Concrete is a large thermal mass. A four inch slab holds a great deal of heat and gives it up slowly, which means its temperature lags the air by many hours and sometimes by a day or more. An Alabama winter afternoon that climbs to sixty-five feels like fine working weather. The slab underneath, which spent the night at thirty-eight and is also in contact with cold ground, may still be in the forties at two in the afternoon.

Coat it on the strength of the air reading and you have just applied resin below its minimum temperature while the thermometer told you everything was fine.

So the measurement that matters is taken on the concrete with an infrared thermometer, at several points across the floor, including along the exterior wall and near the door where it runs coldest. In winter that reading is what decides whether the day goes ahead. The lag cuts the other way too: a slab brought up to temperature over a couple of days holds that heat through a cold night far better than the air does.

Dew point, and the floor that blushes

The other cold-weather failure is condensation, and it is invisible until it has already happened.

When a surface is colder than the dew point of the air around it, moisture condenses on it. That is the film on a cold drink in summer, and a cold slab in a garage does the same thing. The trouble is that a very thin layer of condensation on concrete is not visible. The floor looks dry. You coat it, and the resin is now sitting on a film of water instead of on the concrete.

The industry rule is that the slab must be at least five degrees Fahrenheit above the dew point, and rising rather than falling, through application and the hours after. Rising matters: a slab that is warm enough at four in the afternoon but cooling toward evening can drop through the dew point while the coating is still curing.

Two things show up when this goes wrong. Amine blush is a waxy, sometimes greasy film that forms on curing epoxy when moisture and cool conditions let the hardener react with carbon dioxide instead of with the resin. It looks like a cloudy or oily haze, it is soft, and anything coated over it bonds to the blush rather than to the epoxy. Carbamation is the related defect, a chalky surface from the same cause.

Both are usually fixable if they are caught, by washing the blush off and abrading the surface before the next coat. Both are entirely avoidable by watching the dew point in the first place.

Attached, detached, and why your neighbor’s answer is not yours

Two garages half a mile apart behave like different climates in January.

An attached garage shares at least one wall with a heated house, often has conditioned space above it, and sits inside the building envelope. It drifts well above outside temperature overnight and it is straightforward to bring up to working range and hold there.

A detached garage is a box in a field. It loses heat through every surface, its slab sits on cold ground with no heated structure feeding it, and overnight it will track close to the outside low. Up in Cleburne County and further north into DeKalb, sitting higher up, the winters bite harder than they do in Anniston, and a detached shop on one of those slabs is the hardest version of this job.

Hard is not impossible. It means heat goes in before the work does. Indirect-fired heaters run for a day or two to bring the slab itself up rather than just warming the air, the building gets closed up, and the temperature is held through the cure rather than switched off at five o’clock when the crew leaves.

One caution on heat. Unvented propane and kerosene heaters put water vapor and carbon dioxide into the air as they burn, and both of those feed the blush problem described above. Indirect-fired units that exhaust outside are the right tool. A salamander heater pointed at a curing epoxy floor is a way to create the exact defect you were trying to avoid.

He showed up exactly when promised, did everything he said he would, and the epoxy flooring in my garage and front porch looks amazing.

Belinda M.

What winter actually has going for it

Having listed the complications, the honest conclusion is that winter is a good time to do this.

Humidity is lower. The high summer moisture that makes some chemistries awkward and keeps slabs damp is largely gone, and a garage slab in January is often drier than the same slab in July. For a garage floor system that is a genuine advantage rather than a consolation.

Working time is longer. Summer heat shortens pot life, sometimes dramatically, and a crew racing a batch that is gelling in the bucket is not doing its best work. Cooler conditions give an installer room to spread, broadcast and back-roll properly.

And the calendar is more open. Spring and fall are the busy stretches, so a winter booking generally means a date that suits you rather than the next gap on the schedule.

What to ask if you are booking one now

Two questions will tell you whether somebody runs a winter job properly. Will you be measuring the slab temperature, and what is the minimum for the product you are using. And how are you handling dew point, given the slab will be cold. Specific answers are the whole difference, and vagueness about either one in December is a reason to wait for a different contractor rather than for a different season.

Taylor tests and documents conditions as a matter of course, and the prep and testing side of the work is where that discipline lives. He is on every job himself, which in winter mostly means he is the one reading the slab with the thermometer before anybody opens anything.

Winter is a good month to get this done, and the calendar is quieter. Taylor will read the slab before he commits to a date.

(256) 365-6535 or tell him what the floor is.