Plenty of properties around Oneonta have a second building out past the house. Some began life as a pole barn or a storage shed. Over the years they picked up insulation, wall board, a window unit and a TV on the wall, and now they are an office, a rec room, or the place the family actually spends its evenings.
The floor is nearly always the last thing anyone thinks about. It is usually the original bare slab, and it sheds a fine gray dust onto everything in the room. A flake floor is the most common fix Taylor puts down in these buildings. This is how he goes about one when the room was never designed to be a room.
An outbuilding slab is its own starting point
A house slab and a garage slab tend to be poured to a standard. Detached buildings in Blount County are a different story. Some were placed at the same time as the house. Others went in years later, sometimes in two pours that meet in the middle, sometimes with no thought given to what would ever sit on top.
That is why the first visit to an outbuilding is a proper inspection. Taylor walks the whole slab before anything is said about color. He looks for cracks where the building has settled, for a joint where two pours meet, for the low corner by the door where rain blows in, and for the dark patches where a mower or a tractor dripped oil for a decade.
None of that rules a building out. It decides what has to happen before the flake goes down. A cracked joint gets cut open and filled. A low spot gets built back up. Oil gets ground out as far as it will come. The coating is only as good as the slab underneath it, and in a building nobody planned as living space, the slab usually needs more attention than a garage would.
Ask whether there was ever a vapor barrier
Here is the question that matters most on a detached building, and it is one most owners cannot answer. When a slab goes down, a plastic sheet underneath stops ground moisture rising into the concrete. On houses it is standard. On sheds, barns and shops it was often skipped to save time.
Bare concrete with no barrier gets away with it, because the moisture comes up and simply leaves through the open surface. A flake system closes that surface off. If enough vapor is still moving, it gathers under the new floor with nowhere to escape, and the coating starts to blister or lift.
So on an outbuilding Taylor measures rather than guesses. If the reading comes back fine, the job goes ahead as normal. If it does not, a moisture mitigating primer goes on before the base coat, and you hear about that before any work is scheduled. Finding it out on the first visit is a mild inconvenience. Finding it out after the floor is down means doing the floor twice.
A coved edge lets you wash the room out
Most finished outbuildings around here are lined in OSB or similar board, and the place that board meets the slab is where the trouble collects. Dust drifts into that corner. Mop water runs to it. Anything spilled slides along the wall and soaks into the bottom edge of the board.
A cove fixes that. Instead of the coating stopping flat at the wall, it curves up and runs a short way up the wall itself, so the floor and the bottom of the wall become one continuous surface with no crack between them. Taylor has coved flake up the walls of OSB-lined outbuildings with the window unit and the TV mount already in place, and the difference shows the first time the room gets cleaned.
With a cove you can mop right up to the wall, or even rinse the floor, without water running behind the board. In a building that sees muddy boots, dogs and the occasional spilled drink, that is the feature people end up liking most, more than the color.
Picking a chip blend for the building you have
The color question is real, and it is easier to answer in the building than from a sample card in the kitchen. Outbuildings are often lit by a few overhead fixtures and whatever comes in through one window, so the floor color changes the whole feel of the room.
A gray and white blend is the one people pick most, and for good reason in a building with a door that opens onto gravel or grass. It hides dust and tracked dirt better than anything darker, and it keeps a dim room feeling bright. Blends with a strong color in them work well too. Taylor has laid a blue, black and white flake across a basement with poured concrete walls and wood cabinets, and in a rec room that kind of blend gives the floor some personality.
Whatever the colors, the texture of the chip is what keeps the floor from turning slick when someone walks in from the rain. That matters more in an outbuilding than in most rooms, because people go in and out all day in whatever the weather is doing.
How the job runs out back
The building needs to be empty, which is often the hardest part. Couches, desks, the freezer and the boxes that have lived along the back wall for years all have to go somewhere for the duration. Things fixed to the walls can usually stay where they are.
Taylor needs to get the grinder and the vacuum to the door, so a clear path from the driveway helps. The edges and corners get worked by hand, because a walk-behind machine cannot reach the last few inches along a wall. For a building about the size of a two-car garage, plan on a similar schedule to one, three to four days from grinding to topcoat, with the building closed while the coats go on.
The system itself is a pigmented base, a full broadcast of chip, then a clear topcoat over the top. The flake epoxy page for Oneonta covers how Taylor builds it layer by layer and what goes into the prep.
Questions about flake in an outbuilding
Can the floor be done if the walls are already finished?
Yes, and most are. The wall board stays where it is. Taylor protects the bottom of the walls during grinding, works the edges with a hand grinder, and runs the cove up against the finished surface, so the room never has to be stripped back to the studs.
Will the new floor feel cold or hard underfoot?
A flake system is a thin layer bonded to the concrete, so the floor will feel about the way the slab did, just smooth and clean. It does not add cushion or warmth. Rugs sit happily on top, and the coating makes it easier to clean underneath them when they are lifted.
What if the building doubles as a workshop?
Flake handles foot traffic, furniture and dropped hand tools well. If the space sees a vehicle lift, heavy solvents or rolling equipment every day, a solid color urethane floor may suit it better. Taylor will tell you which one fits how you actually use the building, even if that is not the floor you asked about.
Got a building out back with a dusty slab and plans for it? Taylor will come out, walk the floor with you and give you a real number.