Home About
Services Services Residential Garage Floor Epoxy Flake Epoxy Metallic Epoxy Garage Floors Garage Floor Restoration Non-Slip Epoxy Floor Residential Concrete Floor Polishing Polyurethane Floors Quartz System Self-Leveling Overlays Sleeper System Floor Outdoor Patio Coatings Terrace Restoration Waterproofing Commercial Commercial Epoxy Flooring Commercial Flake Epoxy Commercial Metallic Floors Commercial Floor Painting Commercial Concrete Floor Polishing Prep Concrete Grinding Concrete Sealing Concrete Floor Prep Chemical-Resistant Novolac Epoxy
Areas Service Areas
Blount County, AL Blount County, AL Oneonta, AL
Calhoun County, AL Calhoun County, AL Anniston, AL Jacksonville, AL Oxford, AL Piedmont, AL
Carroll County, GA Carroll County, GA Carrollton, GA Mount Zion, GA Villa Rica, GA
Cherokee County, AL Cherokee County, AL Centre, AL
Clay County, AL Clay County, AL Lineville, AL
Cleburne County, AL Cleburne County, AL Edwardsville, AL Heflin, AL
DeKalb County, AL DeKalb County, AL Fort Payne, AL Rainsville, AL
Etowah County, AL Etowah County, AL Boaz, AL Gadsden, AL Glencoe, AL Hokes Bluff, AL Rainbow City, AL Southside, AL
Floyd County, GA Floyd County, GA Rome, GA
Haralson County, GA Haralson County, GA Bremen, GA Tallapoosa, GA
Jefferson County, AL Jefferson County, AL Birmingham, AL Clay, AL Fultondale, AL Gardendale, AL Irondale, AL Leeds, AL Mountain Brook, AL Pinson, AL Trussville, AL Vestavia Hills, AL Warrior, AL
Marshall County, AL Marshall County, AL Albertville, AL Guntersville, AL
Polk County, GA Polk County, GA Cedartown, GA
Randolph County, AL Randolph County, AL Roanoke, AL
Shelby County, AL Shelby County, AL Chelsea, AL Columbiana, AL Harpersville, AL Pelham, AL Vincent, AL Westover, AL Wilsonville, AL
St. Clair County, AL St. Clair County, AL Argo, AL Ashville, AL Margaret, AL Moody, AL Odenville, AL Pell City, AL Ragland, AL Springville, AL
Talladega County, AL Talladega County, AL Childersburg, AL Lincoln, AL Sylacauga, AL Talladega, AL
Tallapoosa County, AL Tallapoosa County, AL Alexander City, AL Dadeville, AL Daviston, AL New Site, AL
Gallery Blog Contact
Call · (256) 365-6535
Skip to content

Grinding or Acid Etching: What Prep Actually Does

Almost every conversation Taylor has about a coating ends up being a conversation about prep, and it usually starts with the same sentence: the last guy acid etched it. Sometimes that is said as a credential. More often it is said by somebody standing on a floor that let go, trying to work out what went wrong.

Prep is the part of this trade nobody photographs and nobody asks about until it fails. So here is the comparison, laid out honestly, including where etching is a reasonable choice and where it is not.

What a coating actually needs from a slab

Resin does not glue itself to concrete the way tape sticks to glass. It flows into the open pores and the microscopic texture of the surface, cures hard in there, and holds on mechanically. Think of it as thousands of tiny anchors rather than one adhesive bond.

So the whole job of preparation is to produce texture, uniformly, across the entire floor, deep enough for the system going on top. The industry puts a number on it. The Concrete Surface Profile scale runs from CSP 1, which is barely textured, up to CSP 9, which looks like a gravel road. Resin coatings generally call for CSP 2 to 3. That number is printed on the data sheet of whatever product is going down, and it is not a suggestion.

Both grinding and etching are attempts to hit that number. They go about it completely differently and they do not land in the same place.

What acid etching actually does

Etching is a chemical reaction. You wet the slab, apply a dilute acid, usually muriatic or a safer substitute, and it eats the cement paste at the very surface. The reaction fizzes, you neutralize it, you rinse it, and when the water dries the floor feels rougher than it did.

It does roughen a surface. On a soft, porous, open slab that has never been sealed and never been hard-trowelled, etching can get you into the bottom end of CSP 1 to 2. For a thin sealer on a basement floor that was poured rough to begin with, that is sometimes enough.

Here is what it cannot do, and this is the part that gets people.

  • It cannot touch a sealer. Acid reacts with cement. A floor with a cure-and-seal product on it, which most new slabs have, is protected from the acid by the very thing you are trying to remove.
  • It cannot remove a hard-trowelled skin reliably. It lightly opens the top of it in patches and leaves the rest.
  • It cannot remove oil, glue, old paint or tire marks. Any of those sit there and block the reaction, so the floor ends up etched in some places and untouched in others.
  • It leaves residue. Acid plus cement produces salts. Rinse badly, which is easy to do in a garage with one floor drain or none, and those salts stay on the surface. The coating then bonds to a layer of loose powder.
  • It leaves the slab soaking wet. Concrete holds water a long time. Coat it too soon and the moisture trapped underneath pushes the resin back off.

Four of those five failure modes are invisible when you look at the dried floor. It looks prepped. That is the whole problem with etching: the feedback you get is unreliable.

What diamond grinding does differently

A grinder is a machine with diamond-impregnated tooling spinning against the slab under its own weight. It is not cleaning the floor. It is removing a measurable thickness of the floor and leaving a fresh surface behind.

That difference matters in four ways.

It is mechanical, so it does not care what is on top

Sealer, old epoxy, carpet glue, thinset, paint, oil that has soaked in. The diamonds go through all of it and keep going into sound concrete underneath. Nothing has to react with anything.

It is uniform

You can see where you have been. A ground slab has a consistent, visible texture across the whole area, and anywhere you missed is obvious because it still looks different. Etching gives you no such read.

The profile is selectable

Bond and grit of the tooling are chosen for the hardness of the slab and what is on it. The wrong bond either glazes the floor or gouges it, which is why this is a skill rather than a rental. Hit the CSP number the data sheet asks for, verified against a profile chip, and you know what you handed the coating.

It leaves the floor dry

Grinding is a dry process on HEPA extraction, so you are not introducing gallons of water into a slab an hour before you coat it. The dust goes into a vacuum, which also means it can run inside an occupied building without putting a fog through the house.

Where etching is still a defensible choice

Taylor is not going to pretend etching has no use. On a small, raw, never-sealed porch slab taking a penetrating sealer rather than a film, a careful etch and a thorough rinse is a reasonable preparation. The system going on is thin, it penetrates, and the stakes if it fails are low.

What etching is not is preparation for a resin floor you are paying real money for. The gap between CSP 1 and CSP 2 to 3 is where the whole bond lives.

There is also a middle case worth naming, because people ask about it. Shot blasting is the third option, and on a big commercial slab it is often faster than grinding. It fires steel shot at the floor, recovers it, and leaves an aggressive profile, usually CSP 3 and up. It is the right tool for a warehouse or for a thick system that wants a deep key. It is less suited to a home garage, because it is a loud machine that struggles along walls and in corners, and most residential floors want a finer profile than it naturally produces. Grinding handles edges and gets you into the exact range a decorative system asks for.

Why this is the hill Taylor dies on in Calhoun County

This is partly a local argument. A lot of the housing stock around Anniston, Oxford, Jacksonville and Piedmont dates to the fifties through the eighties, built through the depot and mill years, and those garage slabs were power trowelled hard. The surface is tight and closed and almost burnished. It looks like a good floor and it rejects coatings.

That is exactly why so many store-bought garage kits in this county peeled inside a year. The kit instructions were written for an average slab. The slabs here are not average, and acid is not strong enough to argue with a trowelled surface.

Taylor has a lot of knowledge and he is very good at what he’s doing. We absolutely love our new front and back porch!

Keith M.

What to ask whoever is quoting your floor

You do not need to become an expert. You need two answers.

Ask how the slab is being profiled, and listen for the word grinding rather than etching, washing or cleaning. Then ask what CSP profile they are taking it to. Somebody who preps for a living will say 2 to 3 without pausing, because it is printed on the can of whatever they are installing. Somebody who does not will change the subject to the product.

Shanks grinds every floor. He also sells prep on its own to builders, flooring contractors and other coating installers who would rather buy the profile than own the tooling, with moisture and bond numbers written down and handed over. If you want the detail on the grinding side specifically, including coating and glue removal, that page covers it.

Prep is most of the job and none of the glamour. It is also the only part that determines whether the floor is still there in five years.

If somebody told you your slab just needs a good etch, get a second opinion before you pay for a coating.

(256) 365-6535 or tell him what the floor is.