Home About
Services Services Residential Garage Floor Epoxy Flake Epoxy Metallic Epoxy Garage Floors Garage Floor Restoration Non-Slip Epoxy Floor Residential Concrete Floor Polishing Polyurethane Floors Quartz System Self-Leveling Overlays Sleeper System Floor Outdoor Patio Coatings Terrace Restoration Waterproofing Commercial Commercial Epoxy Flooring Commercial Flake Epoxy Commercial Metallic Floors Commercial Floor Painting Commercial Concrete Floor Polishing Prep Concrete Grinding Concrete Sealing Concrete Floor Prep Chemical-Resistant Novolac Epoxy
Areas Service Areas
Blount County, AL Blount County, AL Oneonta, AL
Calhoun County, AL Calhoun County, AL Anniston, AL Jacksonville, AL Oxford, AL Piedmont, AL
Carroll County, GA Carroll County, GA Carrollton, GA Mount Zion, GA Villa Rica, GA
Cherokee County, AL Cherokee County, AL Centre, AL
Clay County, AL Clay County, AL Lineville, AL
Cleburne County, AL Cleburne County, AL Edwardsville, AL Heflin, AL
DeKalb County, AL DeKalb County, AL Fort Payne, AL Rainsville, AL
Etowah County, AL Etowah County, AL Boaz, AL Gadsden, AL Glencoe, AL Hokes Bluff, AL Rainbow City, AL Southside, AL
Floyd County, GA Floyd County, GA Rome, GA
Haralson County, GA Haralson County, GA Bremen, GA Tallapoosa, GA
Jefferson County, AL Jefferson County, AL Birmingham, AL Clay, AL Fultondale, AL Gardendale, AL Irondale, AL Leeds, AL Mountain Brook, AL Pinson, AL Trussville, AL Vestavia Hills, AL Warrior, AL
Marshall County, AL Marshall County, AL Albertville, AL Guntersville, AL
Polk County, GA Polk County, GA Cedartown, GA
Randolph County, AL Randolph County, AL Roanoke, AL
Shelby County, AL Shelby County, AL Chelsea, AL Columbiana, AL Harpersville, AL Pelham, AL Vincent, AL Westover, AL Wilsonville, AL
St. Clair County, AL St. Clair County, AL Argo, AL Ashville, AL Margaret, AL Moody, AL Odenville, AL Pell City, AL Ragland, AL Springville, AL
Talladega County, AL Talladega County, AL Childersburg, AL Lincoln, AL Sylacauga, AL Talladega, AL
Tallapoosa County, AL Tallapoosa County, AL Alexander City, AL Dadeville, AL Daviston, AL New Site, AL
Gallery Blog Contact
Call · (256) 365-6535
Skip to content

A Solid Color Urethane Floor for the Shop Behind the House

Every so often the call from Oneonta is about neither a garage nor a porch. It is about a shop: a metal building behind the house where someone runs a business. It might be engine work, fabrication, detailing or restoring old cars. The work pays the bills, and customers sometimes walk in and see the place.

A floor in that kind of building has a harder life than a garage floor, and it is also part of how the business looks. For a lot of these shops Taylor recommends a solid color floor with a polyurethane topcoat. Here is why, what it does well, and the situations where he would steer you toward something else.

What a working shop asks of its floor

A home garage sees a car or two come and go. A working shop sees a great deal more. Jack stands and floor jacks get dragged across it. Rolling tool chests weighing more than a riding mower roll back and forth on small casters. A lift puts its whole load into a few anchor points. Brake fluid, coolant, oil and cleaning solvents all end up on the floor sooner or later, sometimes in quantity.

Bare concrete handles abuse but stains permanently and sheds dust into everything, including fresh paint and open engines. A basic garage coating looks good at first but can scuff and dull quickly under steel wheels and dragged equipment. The floor has to cope with both the wear and the chemicals, and it has to stay easy to clean, because a shop gets swept and wiped every day.

There is one more demand people underrate. When a customer walks into a shop with a clean, bright floor, the first impression is that the work will be done right. That counts when the shop is behind your house rather than on a commercial strip.

Epoxy underneath, urethane on top

The system is built in two parts, and each layer does a different job. First, after the slab is ground and repaired, an epoxy base goes down in a solid color. Epoxy bonds hard to prepared concrete and builds a thick, even layer that levels out the small hollows in the surface.

Over that goes the polyurethane. Urethane is a tougher topcoat when it comes to scuffing and abrasion, and it stands up to the fluids that get spilled in a shop better than the epoxy base would on its own. It also holds its gloss under traffic that would leave a softer finish looking dull.

Color is chosen at the base coat, since the urethane over it is clear. Light gray is the most common pick for a working shop because it brightens the room and does not show every mark. White makes the most of the light and looks sharp under a finished vehicle. Darker grays hide more but give back less light. Seeing a sample on the actual slab, under the actual fixtures, settles it faster than any photo.

Put together, you get the bond and build of the epoxy with a wearing surface that is made for the punishment. The polyurethane floor page for Oneonta goes through how the layers are put down and what the prep involves for a shop slab.

A bright floor changes a metal building

Metal shops tend to be lit from strip fixtures overhead, and a bare concrete floor swallows a lot of that light. A high-gloss solid floor in light gray or white does the opposite. It reflects the ceiling lights back up, so the whole building gets brighter without adding a single fixture, and the space under a vehicle stops being a dark hole.

Shanks has put down a light gray solid floor in a white metal shop with a loft and two roll doors, and the strip lights show in the floor like a mirror. In another metal building, a white floor holds a clear reflection of a red convertible parked on it. For a business that shows off its finished work, a floor like that does part of the selling.

The honest flip side is that a bright solid floor shows things. Dust, footprints and the odd scratch are easier to see on a plain light color than on a busy flake. Shops that sweep every day rarely mind. A building that gets cleaned once a month may be happier with something more forgiving.

Great experience from start to finish. He showed up exactly when promised, did everything he said he would, and the epoxy flooring in my garage and front porch looks amazing.

Belinda M.

Grip where the shop gets wet

A glossy urethane floor is smooth, and smooth plus oil or water underfoot is a real concern in a building where people work on their feet all day. The answer is a fine grit added to the topcoat. It roughens the surface just enough to give boots some purchase without making the floor hard to sweep.

Grit does not have to go everywhere. A common approach is to add it where the floor actually gets wet: around a wash area, in front of the roll doors where rain blows in, near the sink or the parts washer. The open middle of the floor can stay glossy where the light and the look matter most.

Talk this through before the job, not after. Grit goes in with the final coat, and adding it later means another coat over the whole area.

When polyurethane is the wrong call

Taylor would rather talk you out of a floor than install the wrong one. A solid urethane system is not the answer for every shop.

If the slab has moisture coming up through it, that has to be measured and dealt with first, and in some buildings it changes the plan entirely. If the space is more storage than workshop, a grind and seal may do everything you need. If the floor mostly sees foot traffic and dirt tracked in from a gravel lot, a flake floor will hide the mess better and ask less of you.

Plans matter too. If a lift is going in, or being moved, say so before the floor is done. Drilling anchors through a finished floor is possible, but planning their location first gives a cleaner result.

Shop floor questions

Can I keep working while the floor goes down?

Not in the building itself. The shop has to be completely empty, and nobody works in it from the first grinding pass until the topcoat is ready. Taylor will give you a real schedule up front so you can line up work elsewhere, push jobs back, or plan the floor around a slow stretch.

Will it hold up to the chemicals in my shop?

Polyurethane handles the everyday spills of a working shop well, which is the reason it goes on top. Tell Taylor what you actually use, especially anything unusual or aggressive, so the system can be matched to it. Wiping spills up rather than letting them sit is good practice on any floor.

Can the floor have more than one color?

Yes. Solid floors can carry a different color in a border, a work zone or a walkway, which helps keep customers out of the working area. It takes more planning and more time on site than a single color, so decide on the layout before the work is scheduled.

Running a business out of a shop with a tired floor? Tell Taylor how the building gets used and he will come out to look at the slab.

(256) 365-6535 or set up a visit to the shop.